atmosphere
Module¶
Contains the following atmospheric functions:
density = atm_density(alt, mach)
mach = atm_mach(alt, velocity)
velocity = atm_velocity(alt, mach)
pressure = atm_pressure(alt)
temperature = atm_temperature(alt)
sos = atm_speed_of_sound(alt)
mu = atm_dynamic_viscosity_mu(alt)
nu = atm_kinematic_viscosity_nu(alt)
eas = atm_equivalent_airspeed(alt, mach)
- rho, machs, velocity = make_flfacts_alt_sweep(
mach, alts, eas_limit=1000., alt_units=’m’, velocity_units=’m/s’, density_units=’kg/m^3’, eas_units=’m/s’)
- rho, machs, velocity = make_flfacts_mach_sweep(
alt, machs, eas_limit=1000., alt_units=’m’, velocity_units=’m/s’, density_units=’kg/m^3’, eas_units=’m/s’)
All the default units are in English units because the source equations are in English units.
-
pyNastran.utils.atmosphere.
atm_density
(alt: float, R: float = 1716.0, alt_units: str = 'ft', density_units: str = 'slug/ft^3') → float[source]¶ Freestream Density f$ rho_{infty} f$
- Parameters
- altfloat
altitude in feet or meters
- Rfloat; default=1716.
gas constant for air in english units (???)
- alt_unitsstr; default=’ft’
the altitude units; ft, kft, m
- density_unitsstr; default=’slug/ft^3’
the density units; slug/ft^3, slinch/in^3, kg/m^3
- Returns
- rhofloat
density f$ rho f$ in density_units
- Based on the formula P=pRT
- f[ large rho=frac{p}{R T} f]
-
pyNastran.utils.atmosphere.
atm_dynamic_pressure
(alt: float, mach: float, alt_units: str = 'ft', pressure_units: str = 'psf') → float[source]¶ Freestream Dynamic Pressure f$ q_{infty} f$
- Parameters
- altfloat
Altitude in alt_units
- machfloat
Mach Number f$ M f$
- alt_unitsstr; default=’ft’
the altitude units; ft, kft, m
- pressure_unitsstr; default=’psf’
the pressure units; psf, psi, Pa, kPa, MPa
- Returns
- dynamic_pressurefloat
Returns dynamic pressure in pressure_units
- The common method that requires many calculations…
- f[ large q = frac{1}{2} rho V^2 f]
- f[ large p = rho R T f]
- f[ large M = frac{V}{a} f]
- f[ large a = sqrt{gamma R T} f]
- so…
- f[ large q = frac{gamma}{2} p M^2 f]
-
pyNastran.utils.atmosphere.
atm_dynamic_viscosity_mu
(alt: float, alt_units: str = 'ft', visc_units: str = '(lbf*s)/ft^2') → float[source]¶ Freestream Dynamic Viscosity f$ mu_{infty} f$
- Parameters
- altfloat
Altitude in alt_units
- alt_unitsstr; default=’ft’
the altitude units; ft, kft, m
- visc_unitsstr; default=’(lbf*s)/ft^2’
the viscosity units; (lbf*s)/ft^2, (N*s)/m^2, Pa*s
- Returns
- mufloat
dynamic viscosity f$ mu_{infty} f$ in (lbf*s)/ft^2 or (N*s)/m^2 (SI)
See also
sutherland_viscoscity ..
-
pyNastran.utils.atmosphere.
atm_equivalent_airspeed
(alt: float, mach: float, alt_units: str = 'ft', eas_units: str = 'ft/s') → float[source]¶ Freestream equivalent airspeed
- Parameters
- altfloat
altitude in alt_units
- Machfloat
Mach Number
- $ M
- $
- alt_unitsstr; default=’ft’
the altitude units; ft, kft, m
- eas_unitsstr; default=’ft/s’
the equivalent airspeed units; ft/s, m/s, in/s, knots
- Returns
- easfloat
equivalent airspeed in eas_units
- EAS = TAS * sqrt(rho/rho0)
- p = rho * R * T
- rho = p/(RT)
- rho/rho0 = p/T * T0/p0
- TAS = a * M
- EAS = a * M * sqrt(p/T * T0/p0)
- EAS = a * M * sqrt(p*T0 / (T*p0))
-
pyNastran.utils.atmosphere.
atm_kinematic_viscosity_nu
(alt: float, alt_units: str = 'ft', visc_units: str = 'ft^2/s') → float[source]¶ Freestream Kinematic Viscosity f$ nu_{infty} f$
- Parameters
- altfloat
Altitude in alt_units
- alt_unitsstr; default=’ft’
the altitude units; ft, kft, m
- visc_unitsstr; default=’slug/ft^3’
the kinematic viscosity units; ft^2/s, m^2/s
- Returns
- nufloat
kinematic viscosity f$ nu_{infty} f$ in visc_units
- f[ large nu = frac{mu}{rho} f]
See also
sutherland_viscoscity ..
Todo
better debug ..
-
pyNastran.utils.atmosphere.
atm_mach
(alt: float, V: float, alt_units: str = 'ft', velocity_units: str = 'ft/s') → float[source]¶ Freestream Mach Number
- Parameters
- altfloat
altitude in alt_units
- Vfloat
Velocity in velocity_units
- alt_unitsstr; default=’ft’
the altitude units; ft, kft, m
- velocity_unitsstr; default=’ft/s’
the velocity units; ft/s, m/s, in/s, knots
- Returns
- machfloat
Mach Number f$ M f$
- f[ large M = frac{V}{a} f]
-
pyNastran.utils.atmosphere.
atm_pressure
(alt: float, alt_units: str = 'ft', pressure_units: str = 'psf') → float[source]¶ Freestream Pressure f$ p_{infty} f$
- Parameters
- altfloat
Altitude in alt_units
- alt_unitsstr; default=’ft’
the altitude units; ft, kft, m
- pressure_unitsstr; default=’psf’
the pressure units; psf, psi, Pa, kPa, MPa
- Returns
- pressurefloat
Returns pressure in pressure_units
- .. note:
from BAC-7006-3352-001-V1.pdf # Bell Handbook of Aerodynamic Heatingn page ~236 - Table C.1n These equations were used b/c they are valid to 300k ft.n Extrapolation is performed above that.n
-
pyNastran.utils.atmosphere.
atm_speed_of_sound
(alt: float, alt_units: str = 'ft', velocity_units: str = 'ft/s', gamma: float = 1.4) → float[source]¶ Freestream Speed of Sound f$ a_{infty} f$
- Parameters
- altfloat
Altitude in alt_units
- alt_unitsstr; default=’ft’
the altitude units; ft, kft, m
- velocity_unitsstr; default=’ft/s’
the velocity units; ft/s, m/s, in/s, knots
- Returns
- speed_of_sound, afloat
Returns speed of sound in velocity_units
- f[ large a = sqrt{gamma R T} f]
-
pyNastran.utils.atmosphere.
atm_temperature
(alt: float, alt_units: str = 'ft', temperature_units: str = 'R') → float[source]¶ Freestream Temperature f$ T_{infty} f$
- Parameters
- altfloat
Altitude in alt_units
- alt_unitsstr; default=’ft’
the altitude units; ft, kft, m
- temperature_unitsstr; default=’R’
the altitude units; R, K
- Returns
- Tfloat
temperature in degrees Rankine or Kelvin (SI)
- .. note:
from BAC-7006-3352-001-V1.pdf # Bell Handbook of Aerodynamic Heatingn page ~236 - Table C.1n These equations were used because they are valid to 300k ft.n Extrapolation is performed above that.
-
pyNastran.utils.atmosphere.
atm_unit_reynolds_number
(alt: float, mach: float, alt_units: str = 'ft', reynolds_units: str = '1/ft') → float[source]¶ Returns the Reynolds Number per unit length.
- Parameters
- altfloat
Altitude in alt_units
- machfloat
Mach Number f$ M f$
- alt_unitsstr; default=’ft’
the altitude units; ft, kft, m
- reynolds_unitsstr; default=’1/ft’
the altitude units; 1/ft, 1/m, 1/in
- Returns
- ReynoldsNumber/Lfloat
Reynolds number per unit length in reynolds_units
- f[ large Re = frac{ rho V L}{mu} f]
- f[ large Re_L = frac{ rho V }{mu} f]
-
pyNastran.utils.atmosphere.
atm_unit_reynolds_number2
(alt: float, mach: float, alt_units: str = 'ft', reynolds_units: str = '1/ft') → float[source]¶ Returns the Reynolds Number per unit length.
- Parameters
- altfloat
Altitude in alt_units
- machfloat
Mach Number f$ M f$
- alt_unitsstr; default=’ft’
the altitude units; ft, kft, m
- reynolds_unitsstr; default=’1/ft’
the altitude units; 1/ft, 1/m, 1/in
- Returns
- ReynoldsNumber/Lfloat
the Reynolds Number per unit length
- f[ large Re_L = frac{ rho V}{mu} = frac{p M a}{mu R T} f]
- .. note:
this version of Reynolds number directly calculates the base quantities, so multiple calls to atm_press and atm_temp are not made
-
pyNastran.utils.atmosphere.
atm_velocity
(alt: float, mach: float, alt_units: str = 'ft', velocity_units: str = 'ft/s') → float[source]¶ Freestream Velocity f$ V_{infty} f$
- Parameters
- altfloat
altitude in alt_units
- Machfloat
Mach Number f$ M f$
- alt_unitsstr; default=’ft’
the altitude units; ft, kft, m
- velocity_unitsstr; default=’ft/s’
the velocity units; ft/s, m/s, in/s, knots
- Returns
- velocityfloat
Returns velocity in velocity_units
- f[ large V = M a f]
-
pyNastran.utils.atmosphere.
convert_altitude
(alt: float, alt_units_in: str, alt_units_out: str) → float[source]¶ nominal unit is ft
-
pyNastran.utils.atmosphere.
convert_density
(density: float, density_units_in: str, density_units_out: str) → float[source]¶ nominal unit is slug/ft^3
-
pyNastran.utils.atmosphere.
convert_pressure
(pressure: float, pressure_units_in: str, pressure_units_out: str) → float[source]¶ nominal unit is psf
-
pyNastran.utils.atmosphere.
convert_velocity
(velocity: float, velocity_units_in: str, velocity_units_out: str) → float[source]¶ nominal unit is ft/s
-
pyNastran.utils.atmosphere.
get_alt_for_density
(density: float, density_units: str = 'slug/ft^3', alt_units: str = 'ft', nmax: int = 20, tol: float = 5.0) → float[source]¶ Gets the altitude associated with a given air density.
- Parameters
- densityfloat
the air density in slug/ft^3
- density_unitsstr; default=’slug/ft^3’
the density units; slug/ft^3, slinch/in^3, kg/m^3
- alt_unitsstr; default=’ft’
sets the units for the output altitude; ft, m, kft
- nmaxint; default=20
max number of iterations for convergence
- tolfloat; default=5.
tolerance in alt_units
- Returns
- altfloat
the altitude in feet
-
pyNastran.utils.atmosphere.
get_alt_for_eas_with_constant_mach
(equivalent_airspeed: float, mach: float, velocity_units: str = 'ft/s', alt_units: str = 'ft', nmax: int = 20, tol: float = 5.0) → float[source]¶ Gets the altitude associated with a equivalent airspeed.
- Parameters
- equivalent_airspeedfloat
the equivalent airspeed in velocity_units
- machfloat
the mach to hold constant
- alt_unitsstr; default=’ft’
the altitude units; ft, kft, m
- nmaxint; default=20
max number of iterations for convergence
- tolfloat; default=5.
tolerance in alt_units
- Returns
- altfloat
the altitude in alt units
-
pyNastran.utils.atmosphere.
get_alt_for_pressure
(pressure: float, pressure_units: str = 'psf', alt_units: str = 'ft', nmax: int = 20, tol: float = 5.0) → float[source]¶ Gets the altitude associated with a pressure.
- Parameters
- pressurefloat
the pressure lb/ft^2 (SI=Pa)
- pressure_unitsstr; default=’psf’
the pressure units; psf, psi, Pa, kPa, MPa
- alt_unitsstr; default=’ft’
the altitude units; ft, kft, m
- nmaxint; default=20
max number of iterations for convergence
- tolfloat; default=5.
tolerance in alt_units
- Returns
- altfloat
the altitude in alt_units
-
pyNastran.utils.atmosphere.
get_alt_for_q_with_constant_mach
(q: float, mach: float, pressure_units: str = 'psf', alt_units: str = 'ft', nmax: int = 20, tol: float = 5.0) → float[source]¶ Gets the altitude associated with a dynamic pressure.
- Parameters
- qfloat
the dynamic pressure lb/ft^2 (SI=Pa)
- machfloat
the mach to hold constant
- pressure_unitsstr; default=’psf’
the pressure units; psf, psi, Pa, kPa, MPa
- alt_unitsstr; default=’ft’
the altitude units; ft, kft, m
- nmaxint; default=20
max number of iterations for convergence
- tolfloat; default=5.
tolerance in alt_units
- Returns
- altfloat
the altitude in alt_units
-
pyNastran.utils.atmosphere.
make_flfacts_alt_sweep
(mach: float, alts: List[float], eas_limit: float = 1000.0, alt_units: str = 'm', velocity_units: str = 'm/s', density_units: str = 'kg/m^3', eas_units: str = 'm/s') → Tuple[NDArrayNfloat, NDArrayNfloat, NDArrayNfloat][source]¶ Makes a sweep across altitude for a constant Mach number.
- Parameters
- altList[float]
Altitude in alt_units
- Machfloat
Mach Number
- $ M
- $
- eas_limitfloat
Equivalent airspeed limiter in eas_units
- alt_unitsstr; default=’m’
the altitude units; ft, kft, m
- velocity_unitsstr; default=’m/s’
the velocity units; ft/s, m/s, in/s, knots
- density_unitsstr; default=’kg/m^3’
the density units; slug/ft^3, slinch/in^3, kg/m^3
- eas_unitsstr; default=’m/s’
the equivalent airspeed units; ft/s, m/s, in/s, knots
-
pyNastran.utils.atmosphere.
make_flfacts_eas_sweep
(alt: float, eass: List[float], alt_units: str = 'm', velocity_units: str = 'm/s', density_units: str = 'kg/m^3', eas_units: str = 'm/s') → Tuple[NDArrayNfloat, NDArrayNfloat, NDArrayNfloat][source]¶ Makes a sweep across equivalent airspeed for a constant altitude.
- Parameters
- altfloat
Altitude in alt_units
- eassList[float]
Equivalent airspeed in eas_units
- alt_unitsstr; default=’m’
the altitude units; ft, kft, m
- velocity_unitsstr; default=’m/s’
the velocity units; ft/s, m/s, in/s, knots
- density_unitsstr; default=’kg/m^3’
the density units; slug/ft^3, slinch/in^3, kg/m^3
- eas_unitsstr; default=’m/s’
the equivalent airspeed units; ft/s, m/s, in/s, knots
-
pyNastran.utils.atmosphere.
make_flfacts_mach_sweep
(alt: float, machs: List[float], eas_limit: float = 1000.0, alt_units: str = 'm', velocity_units: str = 'm/s', density_units: str = 'kg/m^3', eas_units: str = 'm/s') → Tuple[NDArrayNfloat, NDArrayNfloat, NDArrayNfloat][source]¶ Makes a sweep across Mach number for a constant altitude.
- Parameters
- altfloat
Altitude in alt_units
- MachsList[float]
Mach Number
- $ M
- $
- eas_limitfloat
Equivalent airspeed limiter in eas_units
- alt_unitsstr; default=’m’
the altitude units; ft, kft, m
- velocity_unitsstr; default=’m/s’
the velocity units; ft/s, m/s, in/s, knots
- density_unitsstr; default=’kg/m^3’
the density units; slug/ft^3, slinch/in^3, kg/m^3
- eas_unitsstr; default=’m/s’
the equivalent airspeed units; ft/s, m/s, in/s, knots
-
pyNastran.utils.atmosphere.
sutherland_viscoscity
(T: float) → float[source]¶ Helper function that calculates the dynamic viscosity f$ mu f$ of air at a given temperature.
- Parameters
- Tfloat
Temperature T is in Rankine
- Returns
- mufloat
dynamic viscosity f$ mu f$ of air in (lbf*s)/ft^2
- .. note:
prints a warning if T>5400 deg R
- Sutherland’s Equationn
- From Aerodynamics for Engineers 4th Editionn
- John J. Bertin 2002n
- page 6 eq 1.5bn